Enum GeometricEffectControlMeasureLineRule
Specifies the rules to transform the input ground control points given as a line.
public enum GeometricEffectControlMeasureLineRule
Fields
Arc90Degrees = 3690 degree arc with ends at vertex 1 and vertex 2. Vertex 3 determines the side of the curve.
Arch = 343 point arched line between vertex 1 and vertex 2. Vertex 3 determines the depth of the arch.
Chevron = 15Chevron with apex at vertex 1 and ends at vertex 2 and vertex 3.
ChevronArrow = 31Chevron arrow centered on vertex 1.
ChevronArrowOffset = 32Chevron arrow centered on vertex 1 offset towards vertex 2.
CircleWithArc = 25Circle centered on vertex 1 with attached arc. Vertex 3 determines the side of the 90 degree arc. If 3 points, vertex 2 determines the length of the arc. If 4 points, vertex 2 determines the radius of the circle and vertex 4 determines the length of the arc.
ClosedHalfCircle = 17Semi-circle with vertex 1 and vertex 2 at the corners.
ConcentricCircles = 38Creates 2 or 3 concentric circles centered on vertex 1. Circle radius is based on vertex location.
CoverageEdgesWithTicks = 12Lines between vertex 1 to vertex 3 and vertex 2 to vertex 4. Angled ticks at the end of the lines and vertex 1 and vertex 2.
CrossedArrow = 30Multipoint arrow. Vertex 1 sets the tip and vertex N the width and back of the arrowhead. Crossed at midpoint between vertex 1 and vertex 2.
CurvedParallelTicks = 35Curved line with ticks. Curve begins on vertex 2 and ends on vertex 3. Ticks on opposite side of vertex 1.
DoubleCurve = 43Creates a dynamic line with alternating curves at vertex 2.
DoubleJog = 26Two lines with jogs with gap in between. If there is 3 points the gap is centered on vertex. If 4 points the gap is defined by second segment.
DoubleJogArrow = 39Creates two dynamic lines with jogs centered on vertex 1.
DoublePerpendicular = 5Two lines perpendicular to the first segment. Length of the lines is determined by vertex 3.
EnclosingRoundedRectangle = 45Creates an enclosing rectangle around the line with rounded corners.
FullGeometry = 0Default: returns the input line.
GapExtentMidline = 14Line centered between first and third segment.
GapExtentWithDoubleTicks = 13Two lines with angled ticks on end. Lines created between first and third segments.
HalfCircleExtended = 10U shaped line with curve between vertex 2 and vertex 3. Control points on vertex 1 and vertex 3.
HalfCircleFirstSegment = 8Half circle centered on the midpoint of first segment. Orientation is opposite vertex 3.
HalfCircleSecondSegment = 9Half circle ending on vertex 2 opposite vertex 1. Diameter is defined by vertex 3.
LineExcludingLastSegment = 28Line between vertex 1 and vertex N-1.
LineWithStraightTicks = 42Creates a dynamic line with vertex 1 in the middle. Vertices 2 and 3 define the length of the ticks and the line.
LinkedChevrons = 40Creates a dynamic line between vertex 1 and 2 connecting two chevrons. Vertex 3 defines the width of the chevrons.
MultivertexArrow = 29Multipoint arrow. Vertex 1 sets the tip and vertex N the width and back of the arrowhead.
OffsetOpposite = 23Single line offset from first segment. Offset to opposite side as vertex 3.
OffsetSame = 24Single line offset from first segment. Offset to same side as vertex 3.
OpenCircle = 11330 degrees circle centered on vertex 1 starting at vertex 2.
OppositeToFirstSegment = 6Lines perpendicular to vertex 3 and the midpoint of the first segment with the length determined by first segment.
Parallel = 20Line between vertex 1 and vertex 2 with a parallel line placed at the width defined by vertex 3.
ParallelOffset = 22Parallels lines offset from first segment. Offset determined by vertex 3.
ParallelOffsetByValue = 46Creates dynamic parallel lines offset from the geometry. The offset is determined by a specified value or a defined attribute.
ParallelWithTicks = 19Line with angled ticks on ends between vertex 1 and vertex 2 with a mirrored parallel line placed at the width defined by vertex 3.
ParallelWithTicksByWidth = 44Creates a dynamic line with angled ticks on the ends between vertex 2 and vertex 3. A mirrored parallel line is placed at the width defined by vertex 2.
PartialFirstSegment = 33Line along first segment, starting at vertex 2 extending in the direction and length of vertex 3.
PerpendicularFromFirstSegment = 1Third vertex to first segment midpoint.
PerpendicularOffset = 27Line perpendicular from midpoint of second segment. End point is offset from second segment. Vertex 1 sets length of line.
PerpendicularToFirstSegment = 21Line perpendicular to the midpoint of first segment. Length X% longer than vertex 2-vertex 3.
PerpendicularToSecondSegment = 3Second segment midpoint to first vertex.
PerpendicularWithArc = 16Line between vertex 1 and vertex 2 with arc off of vertex 2. Cross line is perpendicular to vertex 3.
ReversedFirstSegment = 2Line between vertex 2 and vertex 1. Line begins at vertex 2.
SecondSegmentWithTicks = 4Line between vertex 2 and vertex 3 with ticks on ends.
SegmentThenHalfCircle = 41Creates a dynamic line with a straight segment followed by a half circle. The diameter of the circle is determined by the length of the second segment. Vertex 4 determines the side of the half circle.
TipWithPerpendicularAndTicks = 37Dynamic line perpendicular to segment 1, center on vertex 1 and offset towards vertex 2 with ticks.
TripleParallelExtended = 18Three parallel lines of varying length connected to a base line. The base defined by first segment. Vertex 3 is the end of the longest line.
TriplePerpendicular = 7Three lines perpendicular to the first segment. Length of the lines is determined by vertex 3. Top and bottom lines stop at 80% of first segment.